Motorized Camera Pan Tilt Head

Outdoor Two-Axis Positioners

Position a camera, housing, sensor, antenna, or other top-mounted payload with controlled pan and tilt movement. BIT-CCTV models cover 15–40 kg (33–88 lb) load classes, continuous 360° pan, variable-speed motion, preset positioning, IP66 ingress protection, and Pelco P/D control.

Choose the model by total moving weight, center of gravity, required speed, tilt range, environment, and control interface.

Two-Axis Positioning for Your Camera System

A motorized camera pan tilt head provides powered movement around two axes. The pan axis turns the payload horizontally, while the tilt axis raises or lowers its line of sight. Continuous 360° pan lets the platform keep rotating through a full circle, and programmable presets move the platform to stored viewing directions.

These BIT-CCTV units are independent positioners. The top platform carries equipment selected for the project, such as a camera and lens in a housing, a thermal imager, a sensor, or a compact communications device. The payload’s power, video, and data connections must be planned as part of the complete assembly.

Variable speed supports two different tasks within the same system: slow movement for fine aiming at long focal lengths and faster movement for wide-area scanning or repositioning. A stated preset accuracy of ±0.1° supports repeatable movement to saved positions, while final pointing performance also depends on mounting rigidity, payload balance, and structural deflection.

Choose the Load and Motion Profile First

Start with the complete moving payload, then decide whether the system needs deeper downward viewing, higher load capacity, or faster repositioning. BIT-PT520 is the starting point for compact loads and the broadest downward tilt. BIT-PT540 moves into the 30 kg (66.14 lb) class at more moderate speeds. BIT-PT840 covers the highest load class in its standard build and a separate, lower-load high-speed build.

Use the product cards below to compare the exact load, speed, travel, and interface limits. A model that passes the weight check still needs to pass the center-of-gravity and motion checks explained later on this page.

Motorized Pan Tilt Heads

Side view of the light gray BIT-PT520 outdoor variable-speed pan tilt head with external cable

BIT-PT520 side view; top-mounted payload platform and external cable are visible.

BIT-PT520 Outdoor Variable-Speed Medium-Duty Pan Tilt Head

BIT-PT520 combines a 15 kg (33.07 lb) top-load rating with the broadest standard tilt range and the highest speeds in the medium-duty pair. It suits camera and sensor assemblies that need fine 0.01°/s movement as well as faster scanning.

  • Maximum top load15 kg (33.07 lb)
  • Pan rangeContinuous 360°
  • Tilt range-75° to +40°
  • Pan speed0.01–60°/s
  • Tilt speed0.01–30°/s
  • Presets200; preset accuracy ±0.1°
  • ControlRS485, optional RS422, or RJ45; Pelco P/D
  • Power24 V AC/DC
  • Protection and temperatureIP66; -40°F to 158°F with heater
Front view of the light gray BIT-PT540 30 kg outdoor variable-speed camera pan tilt head

BIT-PT540 front view with the top-load platform centered above the pan base.

BIT-PT540 Outdoor Variable-Speed Medium-Duty Pan Tilt Head

BIT-PT540 raises the top-load class to 30 kg (66.14 lb) while keeping slow, controlled positioning down to 0.01°/s. Its 20°/s maximum pan speed and 10°/s maximum tilt speed fit heavier assemblies that do not require the faster motion of PT520 or the PT840 high-speed configuration.

  • Maximum top load30 kg (66.14 lb)
  • Pan rangeContinuous 360°
  • Tilt range-45° to +40°
  • Pan speed0.01–20°/s
  • Tilt speed0.01–10°/s
  • Presets200; preset accuracy ±0.1°
  • ControlRS485, optional RS422, or RJ45; Pelco P/D
  • Power24 V AC/DC
  • Protection and temperatureIP66; -40°F to 158°F with heater
Front view of the light gray BIT-PT840 high-speed outdoor pan tilt positioner with two external cable groups

BIT-PT840 front view; configuration determines the valid top-load and speed combination.

BIT-PT840 Outdoor High-Speed Heavy-Duty Pan Tilt Positioner

BIT-PT840 serves projects that need either the highest load class in this group or a dedicated high-speed build. Specify the standard 40 kg (88 lb) configuration for up to 30°/s pan and 10°/s tilt, or the 25 kg (55 lb) high-speed configuration for up to 60°/s pan and 30°/s tilt.

  • Standard configuration40 kg (88 lb) top load; pan 0.01–30°/s; tilt 0.01–10°/s
  • High-speed configuration25 kg (55 lb) top load; pan up to 60°/s; tilt up to 30°/s
  • Pan rangeContinuous 360°
  • Standard tilt range-45° to +45°
  • Presets255; preset accuracy ±0.1°
  • ControlStandard RS485; optional RS422, RS232, or Ethernet; Pelco P/D
  • ProtectionIP66

Payload Capacity Depends on More Than Weight

Calculate the moving payload from every item carried by the axes: camera, lens, housing, mounting plate, connectors, adapters, and the moving portion of each cable. A 15 kg assembly with a long offset can place more torque on the tilt axis than a compact assembly of the same weight because the center of gravity acts through a longer lever arm.

The motion profile changes the demand again. Rapid acceleration, frequent reversals, and a high rotational inertia require more drive torque than slow scanning at the same payload weight. Outdoor systems also need allowance for wind acting on the projected area of the housing or sensor package. Stiff cables and hoses can add resistance and disturb repeatable movement.

If the center of gravity is far from an axis, the assembly presents a large frontal area, or the duty cycle includes rapid reversals, a lower nominal payload can be the more demanding application. A dimensioned assembly sketch gives BIT-CCTV the geometry needed to review that condition.

Plan Control, Power, and Cabling Together

Pelco P/D defines the control commands, while RS485, RS422, RS232, and Ethernet describe different physical or network interfaces. A controller must match both the interface and the protocol settings. For serial control, confirm the device address, baud rate, wiring polarity, and command set before commissioning.

BIT-PT520 and BIT-PT540 support RS485 with optional RS422 or an RJ45 configuration and operate from 24 V AC/DC. BIT-PT840 uses RS485 as standard, with RS422, RS232, or Ethernet available as options. Its product configuration determines the required DC input. Confirm the selected electrical build before specifying the power supply or site wiring.

Continuous pan rotation also makes cable routing part of the motion design. Stiff or poorly routed moving cables can resist rotation and reduce repeatability, while large connectors or numerous conductors can exceed the available pass-through arrangement. The electrical layout therefore influences both the internal wiring configuration and the mechanical behavior of the finished system.

Where Two-Axis Positioning Changes the System

Repeatable patrol views

A fixed-site camera or thermal imager can move to stored directions instead of requiring one device for every viewpoint. Preset tours suit perimeter, traffic, industrial-site, and infrastructure observation where the system revisits known zones. The useful result depends on a rigid mounting structure: movement in a pole or bracket shifts the view even when the head reaches the same commanded angle.

Fine aiming at long focal lengths

Small angular changes create large shifts in the observed area when a camera uses a long lens. Low-speed movement helps an operator settle on a distant subject without overshooting. On BIT-PT520 and BIT-PT540, zoom-adaptive control can reduce pan and tilt speed as magnification increases. Payload balance and structural stiffness become more visible at these narrow fields of view because vibration and backlash appear as image movement.

Coordinated camera, sensor, and communications payloads

The top platform can carry an integrated assembly rather than a bare camera. A housing may combine visible and thermal imaging, or a positioning system may carry a sensor or compact communications device. This approach keeps the payloads pointed together, but every mounted component changes total weight, center of gravity, inertia, wind area, and cable demand.

Outdoor deployment

All three models carry an IP66 rating for dust and water ingress. PT520 and PT540 are specified for operation from -40°F to 158°F when equipped with a heater.

Ingress protection does not make the surrounding installation mechanically stable. The foundation, pole, bracket, and fasteners must resist the combined static load, motion reaction, wind, and site vibration. Connector sealing and corrosion protection also need to match the local exposure.

Frequently Asked Questions

Does the pan tilt head include a camera?

No. These products are motorized two-axis positioners for a separately selected camera, housing, sensor, antenna, or similar payload. The complete system must match the positioner mechanically and electrically.

Will any Pelco P/D controller work immediately?

The controller must match the unit’s interface and serial settings as well as the Pelco protocol. Confirm RS485/RS422 wiring, address, baud rate, and supported commands; Ethernet configurations also require the selected network implementation to match the host system.

Can the positioner report or receive an absolute angle?

The three models support absolute positioning and angle feedback functions, but the available feedback mode depends on the selected interface and configuration. Specify whether the host needs angle queries, real-time feedback, or direct absolute-position commands so the control build can be matched to it.

Request a Pan Tilt Recommendation

Tell us what the head will carry and how it needs to move. Blue Icon (Tianjin) Technology Co., Ltd. will use your load, motion, and integration requirements to discuss a suitable BIT-CCTV model and configuration.

  • Phone: 86-139-2068-8922
  • Email: [email protected]
  • Address: F9, Macalline Business Center, No. 29, Heiniucheng Rd., Hexi District, Tianjin, China

Your pan tilt requirements will be reviewed using the payload and motion details you provide.