Don't assume that just because the casing is made of stainless steel or has an IP66 mark on it, you can just shove it into a dangerous area. Choosing the ATEX explosion-proof camera shield is useless just by looking at its appearance and waterproof rating. What is the core soul here? It is the complete explosion-proof certification of this specific model, whether it can cover your field conditions! Moreover, after the camera is installed, is this “combination” still within the scope allowed by the family certificate? To put it bluntly, ordinary industrial shields and anti-corrosion shields are completely different from explosion-proof shields that are actually used to carry out work in dangerous areas. No matter how hard you use the materials or how badly you seal them, it can't replace a solid explosion-proof certification for hazardous areas.
First find out the scene, then stick to the nameplate
If you are only told on the spot “this is Zone 2 (Zone 2), Zone 21 (Zone 21) or Zone 22 (Zone 22)”, you will definitely be blinded if you use this information to choose a shield. Zone 2 refers to an environment where there is basically no gas danger during normal operation; Zone 21 is where combustible dust occasionally appears, and Zone 22 is a place where dust danger is basically not even seen. It's not unreasonable to say that the area code can only indicate the frequency of danger, and it doesn't determine which explosion-proof type of equipment you should use. The rules for the gas and dust zones are completely different. You can't just look at the two area code numbers being close together and force the shield of that zone to use in that zone.
It's useless to just stare at the letters “ATEX”; the word itself has no specific restrictions. You need to take the actual working conditions on site and reconcile them word for word with the explosion-proof documents of the equipment. The corresponding gas or dust group, temperature group, equipment protection level (EPL), and ambient temperature range ——none of these complete certification marks and certificate conditions are acceptable. If any one of them doesn't match, even if the brand is loud, the product name is awesome, or the performance of other devices of the same model is good, you should never make do with it.
When checking the certificate, keep a close eye on the specific model you want to use. The manufacturer, model, version number, standards implemented, issuing authority, and whether the certificate has expired must all be checked one by one. Some manufacturers use certificates for other products in the same series to deceive people, which is absolutely not acceptable. As for those small explosion-proof icons printed in the brochure, just look at them; they don't represent the true limitations of this shield at all. What we need to check is the solid equipment and its exclusive certificate in your hand. Don't listen to the manufacturer bragging about how durable their brand series is.
Different explosion-proof types, all operating conditions have changed
There are many doors inside the protective covers used in dangerous areas: some are explosion-proof, some are dust-proof, and some are positive pressure explosion-proof. The explosion-proof principles are different, and the corresponding certification structures and usage conditions are completely different. Don't just call them all “explosion-proof shells”. I really thought they could be used interchangeably after I bought them. As for what IP, IK, or NEMA ratings are marked on the casing, that only refers to routine protection and testing. IP66 is indeed waterproof, but it can't prevent explosions! No matter how good the stainless steel is, you won't get an automatic “pass” for dangerous areas.
If you encounter positive pressure explosion-proof equipment, you'll have to open your eyes wide. Positive pressure protection that is truly made according to explosion-proof standards relies entirely on hard indicators: specified ventilation volume, pressure monitoring, alarm or interlock cut-off function, emission path, and a set of dead rules for safe activation. Some shields look quite intimidating, can be inflated and pressurized, and have a good seal, but as long as they are not certified, they must never be used as positive pressure explosion-proof equipment. If the ventilation and pressure conditions required for this shield cannot be met on site, you can just buy an empty shell and go back, which is still a piece of non-compliant scrap metal.
The inside of the shield is also a road “red line”

Don't think you can just plug a camera into a certified explosion-proof shell by spending a lot of money. The cameras, lenses, and electrical loads you put in there must all be kept in the circle permitted by the certificate. When it comes time to assemble it, the size, interface, operating temperature, and power supply method all need to be sieved. If the size is just right, but the electrical load inside exceeds the standard, it's all for nothing; if the load doesn't exceed the limit, but it takes up space for lens extension and retraction, or blocks the cable arrangement space at the end, you can't do this job. In addition, the operating temperature cannot be determined solely by how much the shell is nominally capable of carrying, nor by the actual heating of the camera inside. The two red lines inside and outside must be checked separately. When the zoom lens is extended and retracted, it must never rub against the front glass window or internal parts. After plugging in the tail connector, there must be enough room for bending on the cable side.
The cable inlet is the place where people are most likely to fall behind, and the entire explosion-proof structure may be destroyed here. The outer diameter and shape of the cable must be tightly fitted to the explosion-proof Glan head (sealing sleeve) clamping range specified in the instruction manual; the appearance of the joint must also match the design of the wire opening. Beyond this range, any sealing or tensile resistance becomes nonsense. You have to remember this: the inlet, plug, explosion-proof joint surface, and those fastening bolts on the explosion-proof or dust-proof housing are all part of the certification structure. Don't go to the hardware store and buy some ordinary parts and replace them! Once you move these core components, the original explosion-proof certification conclusion of this equipment will be immediately invalidated.
Post-installation, opening, replacement of accessories and daily maintenance are all required. Every step must follow the rules in the exclusive certificate and instruction manual, and there must be no ambiguity. To reiterate: sealing sleeves, plugs, joint surfaces, and fasteners must never be replaced privately or modified by the manufacturer. If it is a positive pressure device, before turning it on, honestly complete the prescribed ventilation and pressure confirmation process; if you find that the pressure is wrong during operation, quickly press the interlock or safety procedures to deal with it. Ultimately, whether this equipment can be used in the end depends entirely on the on-site working conditions, the dead rules on the certificate, and whether the final state after you assemble it complies with the rules.