Blue Icon (Tianjin) Technology Co., Ltd.
Blue Icon (Tianjin) Technology Co., Ltd.

Products

Contact Us

How To Connect Multiple Ptz Camera To Controller

Most people who have worked on large outdoor security systems have encountered this embarrassing situation: the surveillance screen on the big screen looks fine, but no matter how hard you pull it on the joystick keyboard, the gimbal in the distance will not move. Why? Because the screen and controls are not on the same track at all. The video line only takes care of the picture, and the control line only takes care of you turning your head up, down, left, and right, making a sudden stop, or adjusting the preset position. If you want to connect a bunch of monitoring points into one controller, you not only have to make the controller recognize who is who, but also ensure that the instructions issued can accurately reach the device that needs to be moved.

First determine who the order is issued to

When talking about how to connect multiple ptz camera to controller, we need to first understand what you are controlling. If you are using a large independent gimbal with a separate cannon barrel camera mounted on it, you should know that the gimbal is only responsible for driving the device to turn left and right and look up and down. As for the lens to be zoomed in and out (zoom), you usually have to use another control line. When encountering a camera position that requires remote focus adjustment, you must confirm whether your control console can issue the corresponding instructions to the lens individually.

Before buying a controller, you need to calculate how many devices its capacity can accommodate. More importantly, you need to compare the interface and control protocol one by one. Take the most common RS-485, for example. These letters only tell you the physical standards of wiring. As for whether the device can understand the commands “turn” and “stop”, it all depends on whether the “language” on both sides of the controller and the gimbal is compatible, that is, the control protocols must be correct.

Use address to distinguish gimbals on the serial bus

If you plan to string a bunch of machines together with RS-485, remember a dead end: each gimbal on the same bus must have its own unique “house number” (address), but the control protocols and serial port parameters they communicate (such as baud rate, data bits, checksum stop bits) must be exactly the same. Take the BIT-PT410 as an example. It has a dial switch (DIP) on its motherboard, which is used to set the address and choose between Pelco P and Pelco D protocols. The factory default parameters in the manual are usually “address 1, Pelco D protocol, baud rate 9600”. If you don't change the dialing code and connect several machines with all addresses 1, the controller will definitely be confused and it will be difficult to tell who to call.

When wiring, remember to disconnect the power first! Follow the instructions on both sides to identify the positive and negative terminals before connecting. As for how the line should be routed, which nodes should be equipped with terminal resistors or biased, how many machines can be strung, and how far the line can be stretched, don't rely on your feelings. Follow the manufacturer's rules honestly, and don't forget to install the terminal resistors in the specified positions. If you are encountering an RS-422 interface, you will have to look up its wiring diagram separately. The rules for multi-device connections are not quite the same as those for 485.

Network control added by device

Many systems are now controlled via the network. This requires assigning each device a unique IP address. When adding a device to the controller, the IP, port number, control protocol, and account password authentication must be filled in one by one according to their respective parameters. Don't think that plugging several machines into the same LAN will do everything right. If the controller can't read their protocols, it's still useless. Sometimes you can already see the picture using RTSP streaming, but you still need to verify separately on the console whether the corresponding control port is connected.

Whether you are playing with 485 serial port or using network IP, the name you give to each camera in the controller must be perfectly matched with its actual address or IP. Otherwise, you want to look at the gate, but when you push the joystick, the gimbal over there in the parking lot turns.

Test each point and then determine the fault range

After connecting the wires and powering on the test machine for the first time, do not push the joystick hard as soon as you start. Select each device on the keyboard and push it gently to make it move slowly and slightly to confirm that it is indeed the gimbal you selected that is moving. There is no problem. Then check whether the up, down, left, and right directions are reversed, whether the release can stop immediately, and whether the turn has limit protection. For camera positions that require zoom and preset, remember to go through these functions separately.

image.png

How to check if you encounter someone who is disobedient? If it is a serial bus, and there is only one machine “playing dead”, then focus on checking whether there are any problems with its own dialing address, the branch line connected to it, or the interface. If the machines on the entire line go on a collective strike, we have to investigate from the source: see if the controller output sends a signal, whether the positive and negative terminals are connected backwards, whether the common parameters such as baud rate are correct, or simply that the main line is broken in the middle. If you push the joystick, several machines will spin along with it, or some machines will move randomly on their own. This is mostly because you use duplicate addresses, or it is caused by improper bus routing, signal reflection without terminal resistors, or improper grounding. Checking in these directions can basically identify the problem.


Related Articles

We use cookies to offer you a better browsing experience, analyze site traffic and personalize content. Part of the tracking is necessary to ensure SEO effectiveness,
By using this site, you agree to our use of cookies. Visit our cookie policy to learn more.
Reject Accept