The surveillance footage is out, but the camera doesn't move when you press the arrow keys? When we encounter this, we have to separate “picture” and “action”. The ability to play RTSP videos normally indicates that there is nothing wrong with the video link. The exact path taken by the control commands issued by the directional keys and whether the device has received and executed them need to be confirmed separately.
In outdoor split-type surveillance systems, the camera is usually mounted on a separate gimbal. The gimbal is responsible for turning the camera left and right and looking up and down, while zooming is done by the camera or lens' own control line. So in this type of system, how to control a ptz camera actually controls two parts of the action: the arrow keys control the gimbal to change direction, and the zoom keys are responsible for zooming in and out of the lens.

How to operate direction, speed and zoom
Whether you tap the hardware control keyboard or click the software interface, you can issue commands. If a three-axis joystick is used, the first two axes are generally used for horizontal and pitch, and the third axis is used for zoom. However, if you change the handle, it all depends on how the control end is configured in the background to determine what action the third axis corresponds to and whether the joystick is in the right direction or wrong. As for whether the amplitude of the push stick can change the rotation speed, it depends on whether the software has done a good mapping, whether the speed field is included in the protocol, and whether the device itself does not support it.
When testing for the first time, it's recommended to give it a gentle push and try horizontal and up and down at a low speed and short distance to see if the direction is correct and if you can stop immediately after letting go. Once you've confirmed that there's no problem, go to the single zoom test.“ Continuous movement ”and “stop” are actually two completely independent instructions. If the gimbal is still spinning after you let go, don't rush to determine that the device is broken. First, check whether the joystick has completely returned to the center, whether the dead zone is set correctly, and whether the control end has issued the “stop” command. If the gimbal listens to the command and hits which one to point, but the lens just can't zoom, then you can just follow the clues to check the control line of the lens.
There is a screen but it cannot be transferred, check which control chain
If it is serial control, RS485 or RS422 controls how physical signals are transmitted, while Pelco D or Pelco P protocols control “what to say”. Connecting the wires correctly is only the first step; the device addresses, protocols, and baud rates at both ends must be perfectly aligned. Take the BIT-PT410 model for example. It supports both 485 and 422, and the protocol is either Pelco P or D. The instructions “address 1, Pelco D, 9600 bps” are just a reference example. In practice, you need to dial or set it according to the device's current actual code.
If network control is used, even if the device and the control end are in the same local area network, what actions can be achieved depends on the functional support of each side. For example, when using ONVIF PTZ, just looking at the ONVIF flag does not mean that all functions are compatible. You need to check the function lists of the corresponding versions on both sides to verify whether the specific actions of continuously moving, stopping or calling preset positions are really connected.
Return to fixed position, cruise and scan
If you need to stare at a specific location frequently, saving a preset location is definitely the easiest. The preset position can remember the level and pitch angle of the gimbal, but whether it can also remember the focal length of the lens at that time depends on the specific equipment. Many engineering brothers have encountered situations where the gimbal can be turned back accurately, but the lens picture is still blurry (focal length has not been restored). At this time, you can check whether the DIP dial switch corresponding to the lens preset function is turned on.
Cruising and scanning are also different: cruising is to have the gimbal turn back and forth sequentially between several preset positions; scanning is to sweep back and forth between the left and right boundaries you set. Take the BIT-PT410 as an example; it binds these two actions to different preset bit numbers. You call number 98 directly and it starts cruising; if you set numbers 92 and 93 to the left and right boundaries respectively, and then call number 99, it starts scanning. Of course, if you are using another brand or model, remember to look through its manual to clearly distinguish which numbers are actually used to store locations and which are used as “shortcut keys” to trigger actions.